Models
>
46-2857-23-02
46-2857-23-02 Tappan Washer - Overview
Sections of the 46-2857-23-02
[Viewing 7 of 7]Keep searches simple, eg. "belt" or "pump".
![Water Inlet Valve – Part Number: 134190200 Water Inlet Valve – Part Number: 134190200](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/815509-1-S-Frigidaire-134190200-Water-Inlet-Valve.jpg)
Water Inlet Valve
PartSelect #: PS815509
Manufacturer #: 134190200
This washing machine water inlet valve has two ports for water to enter.
$162.38
In Stock
![High Temperature Adhesive – Part Number: 5308027429 High Temperature Adhesive – Part Number: 5308027429](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/474458-1-S-Frigidaire-5308027429-High-Temperature-Adhesive.jpg)
High Temperature Adhesive
PartSelect #: PS474458
Manufacturer #: 5308027429
Used for installing felt and rubber seals on dryers.
$68.93
In Stock
![Washer Bolt – Part Number: 137539500 Washer Bolt – Part Number: 137539500](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/3655064-1-S-Frigidaire-137539500-Washer-Bolt.jpg)
Washer Bolt
PartSelect #: PS3655064
Manufacturer #: 137539500
Holds plated on Trunion .312-18 x 1.625.
$23.90
In Stock
![Upper Lip Seal – Part Number: 5303161307 Upper Lip Seal – Part Number: 5303161307](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/454174-1-S-Frigidaire-5303161307-Upper-Lip-Seal.jpg)
Upper Lip Seal
PartSelect #: PS454174
Manufacturer #: 5303161307
This seal goes on top of the transmission below the agitator drive block.
$25.54
Special Order
![Transmission Assembly – Part Number: 134735700 Transmission Assembly – Part Number: 134735700](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/1524603-1-S-Frigidaire-134735700-Transmission-Assembly.jpg)
Transmission Assembly
PartSelect #: PS1524603
Manufacturer #: 134735700
This part aids in the spinning or agitating cycles.
$1041.15
In Stock
Questions And Answers for 46-2857-23-02
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 46-2857-23-02
[Viewing 4 of 4]Leaking
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/815509_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/466832_1_S.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/473382_1_s.jpg)
Show All
No hot or cold water
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/815509_1_s.jpg)
Show All
Marks left on clothes
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/474458_1_S.jpg)
Show All
Noisy
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/474458_1_S.jpg)
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Parts Used:
-
alvaro from east hampton, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
86 of 96 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Cold Water
Checked problem on-line and discovered it was the water inlet valve. Matched the part on part select. Com. Finding the part was very easy. Part select had a grid behind the picture to help determine the size and pictures from all sides. Removing the old part, matching it, and replacement took a total of 30 minutes. I now have clean clothes.
Parts Used:
-
Mark from Pittsburgh, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
16 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water continued to flow into machine during spin cycle
After moving machine to an area that allowed easy access to the unit, disconnected the water supply hoses from the inlet valve.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, disconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.
Removed the two screws that keep the back in place, removed the clips that keep the top in place, moved the top over far enough to get the valve out. Removed the screw that keeps the inlet valve in place, disconnected the power supply to the valve, Pulled valve out in order to remove the water outlet hose. Repalced with new vale, and reversed order to install. Works just fine now.
Parts Used:
-
Howard from Lcolnton, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
16 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!