Models
>
DLW330RAW
DLW330RAW (PDLW330RAW) Amana Washer - Overview
Sections of the DLW330RAW
[Viewing 9 of 9]Keep searches simple, eg. "belt" or "pump".
![Thrust Washer – Part Number: WP233520 Thrust Washer – Part Number: WP233520](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11740482-1-S-Maytag-WP233520-Thrust-Washer.jpg)
Thrust Washer
PartSelect #: PS11740482
Manufacturer #: WP233520
This washer is 3/4 inches in diameter.
$10.11
In Stock
![Hose Clamp – Part Number: WP596669 Hose Clamp – Part Number: WP596669](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11743008-1-S-Maytag-WP596669-Hose-Clamp.jpg)
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
$11.68
In Stock
![Hose Clamp – Part Number: WP285655 Hose Clamp – Part Number: WP285655](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11740613-1-S-Maytag-WP285655-Hose-Clamp.jpg)
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
This hose clamp is sold individually.
$14.11
In Stock
![Adjustable Leveling Leg – Part Number: 22003428 Adjustable Leveling Leg – Part Number: 22003428](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/2021026-1-S-Maytag-22003428-Adjustable-Leveling-Leg.jpg)
Adjustable Leveling Leg
PartSelect #: PS2021026
Manufacturer #: 22003428
Sold Individually. This adjustable leveling leg comes with a stop nut.
$23.49
In Stock
![Retaining Ring – Part Number: WP23748 Retaining Ring – Part Number: WP23748](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11740487-1-S-Maytag-WP23748-Retaining-Ring.jpg)
Retaining Ring
PartSelect #: PS11740487
Manufacturer #: WP23748
This metal retaining ring is well under an inch long. Use it for your Maytag brand clothes washer or your clothes dryer.
$17.27
In Stock
![Spin Belt – Part Number: WP27001007 Spin Belt – Part Number: WP27001007](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11740578-1-S-Maytag-WP27001007-Spin-Belt.jpg)
Spin Belt
PartSelect #: PS11740578
Manufacturer #: WP27001007
This v-shaped spin belt helps transfer power from the motor to the transmission to help pump the water in and out of the washer. It also helps runs the spin cycle in the washer.
$106.82
In Stock
![Inlet Hose - 5 FT – Part Number: WP89503 Inlet Hose - 5 FT – Part Number: WP89503](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11746820-1-S-Maytag-WP89503-Inlet-Hose-5-FT.jpg)
Inlet Hose - 5 FT
PartSelect #: PS11746820
Manufacturer #: WP89503
This hose can handle hot or cold water and is five feet long.
$27.37
In Stock
![Lid Hinge Mounting Screw – Part Number: WPW10119828 Lid Hinge Mounting Screw – Part Number: WPW10119828](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11748588-1-S-Maytag-WPW10119828-Lid-Hinge-Mounting-Screw.jpg)
Lid Hinge Mounting Screw
PartSelect #: PS11748588
Manufacturer #: WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$11.68
In Stock
![Spring Retaining Clip – Part Number: WP22001650 Spring Retaining Clip – Part Number: WP22001650](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11739294-1-S-Maytag-WP22001650-Spring-Retaining-Clip.jpg)
Spring Retaining Clip
PartSelect #: PS11739294
Manufacturer #: WP22001650
This front cover spring retaining clip is not quite an inch long. It is made entirely of metal and is used for some washing machines.
$14.11
In Stock
![Drain Pump – Part Number: 27001233 Drain Pump – Part Number: 27001233](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/1594294-1-S-Maytag-27001233-Drain-Pump.jpg)
Drain Pump
PartSelect #: PS1594294
Manufacturer #: 27001233
This pump is attached to the motor and helps expel water from the washing machine. It is activated after the spin speed is maintained for a specific period of time.
No Longer Available
![Drain Hose with Rubber Elbow – Part Number: WP40053901 Drain Hose with Rubber Elbow – Part Number: WP40053901](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11742254-1-S-Maytag-WP40053901-Drain-Hose-with-Rubber-Elbow.jpg)
Drain Hose with Rubber Elbow
PartSelect #: PS11742254
Manufacturer #: WP40053901
This hose attaches to the pump to help remove the water out of the washer. 7 feet in length.
$69.91
In Stock
![Idler Pulley Wheel – Part Number: WP40045001 Idler Pulley Wheel – Part Number: WP40045001](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/11742250-1-S-Maytag-WP40045001-Idler-Pulley-Wheel.jpg)
Idler Pulley Wheel
PartSelect #: PS11742250
Manufacturer #: WP40045001
This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.
$81.01
In Stock
Questions And Answers for DLW330RAW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the DLW330RAW
[Viewing 7 of 7]Leaking
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/1594294_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11742254_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11743008_1_S.jpg)
Show All
Noisy
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11740482_1_S.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11740487_1_S.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11742857_1_s.jpg)
Show All
Burning smell
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11740578_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11742250_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/2041050_1_s.jpg)
Show All
Will not agitate
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11740578_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11742250_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11740482_1_S.jpg)
Show All
Will not drain
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/1594294_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11740578_1_s.jpg)
Show All
No hot or cold water
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/2167007_2_S.jpg)
Show All
Spins slowly
Fixed by
these parts
these parts
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11742250_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11740578_1_s.jpg)
![Fixing](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/assets/PartImages/11740482_1_S.jpg)
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Belt wore out
Had to remove pump-not easy. Nothing wrong with pump, but had to trash it to get it off the motor shaft, so I had to replace it, too.
Pop up top of cabinet and remove front panel. (I leaned unit back against a wall to facilitate internal access once panel was removed.)
Remove motor assy - 4 screws & connector.
Remove 3 pump screws (torx) and 2 hoses. Pry pump off motor shaft (not easy). I used a heat gun to help expand the plastic fitting on the motor shaft.
Remove old belt, put on new belt. (Do not use automotive belt-this belt is designed to slip because it also spins the tub. The tub will not spin when it's full of water, and the pump will not pump the water if the tub is bogging down the pump. Plus, you will probably overheat the motor.)
Press new pump back on motor shaft (advise not to re-use old pump as seals were probably damaged by removal process.)
Caution: Pressing pump onto motor shaft may cause pump rotor to bind in housing. Try to press it on a little too far so you back off slightly.
Replace pump screws.
Replace motor, giving attention to belt alignment.
Replace motor screws and connector.
Re-attach hoses on pump.
Button up cabinet.
Done.
The hardest part was removing the pump. If not for that, it would have been a 15-min, $20 repair.
Because I felt it wise to replace the pump also, it was a $70 repair.
Pop up top of cabinet and remove front panel. (I leaned unit back against a wall to facilitate internal access once panel was removed.)
Remove motor assy - 4 screws & connector.
Remove 3 pump screws (torx) and 2 hoses. Pry pump off motor shaft (not easy). I used a heat gun to help expand the plastic fitting on the motor shaft.
Remove old belt, put on new belt. (Do not use automotive belt-this belt is designed to slip because it also spins the tub. The tub will not spin when it's full of water, and the pump will not pump the water if the tub is bogging down the pump. Plus, you will probably overheat the motor.)
Press new pump back on motor shaft (advise not to re-use old pump as seals were probably damaged by removal process.)
Caution: Pressing pump onto motor shaft may cause pump rotor to bind in housing. Try to press it on a little too far so you back off slightly.
Replace pump screws.
Replace motor, giving attention to belt alignment.
Replace motor screws and connector.
Re-attach hoses on pump.
Button up cabinet.
Done.
The hardest part was removing the pump. If not for that, it would have been a 15-min, $20 repair.
Because I felt it wise to replace the pump also, it was a $70 repair.
Parts Used:
-
Bruce from Medina, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set
190 of 219 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive Pump Leaked
It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on.
Parts Used:
-
Stephen from Laveen, AZ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
73 of 90 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking on floor from "mysterious place underneath washer"
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.
I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).
So, I finished draining, removed the hose (required pliers to squeeze off a hose clamp).
Upon inspecting the hose, it was also apparent that the hole was caused by rubbing against a support bracket for the motor. This should not happen, but it did because the plastic standoff supposed to keep the hose away from the bracket was installed 180 degrees backwards.
So, I simply replaced the hose and turned the bracket around to the correct orientation.
Everything worked as planned and my repair cost was much less than if I had called someone out.
I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).
So, I finished draining, removed the hose (required pliers to squeeze off a hose clamp).
Upon inspecting the hose, it was also apparent that the hole was caused by rubbing against a support bracket for the motor. This should not happen, but it did because the plastic standoff supposed to keep the hose away from the bracket was installed 180 degrees backwards.
So, I simply replaced the hose and turned the bracket around to the correct orientation.
Everything worked as planned and my repair cost was much less than if I had called someone out.
Parts Used:
-
Bryan from Chicago, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Socket set
50 of 55 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!