Models
>
GTWN2800D1WW
GTWN2800D1WW General Electric Washer - Overview
Sections of the GTWN2800D1WW
[Viewing 4 of 4]Manuals & Care Guides for GTWN2800D1WW
Click to downloadInstall
Installation Instructions
(1.65MB)
Manual
Owner's Manuals
(4.69MB)
Manual
Owner's Manuals
(4.05MB)
Keep searches simple, eg. "belt" or "pump".
Tub Dampening Strap
PartSelect #: PS271100
Manufacturer #: WH1X2727
Your washer uses 4 tub dampening straps. It is recommended to replace all 4 at the same time. They keep the tub in the center of the cabinet and are sold individually.
$16.70
Special Order
Timer Knob
PartSelect #: PS1482286
Manufacturer #: WH01X10310
This replacement timer knob for your washer is white in color.
$22.80
Special Order
Control Knob and Clip - White
PartSelect #: PS9493075
Manufacturer #: WE01X20378
This knob and clip set is an OEM replacement part for your washer or dryer. The knob accepts a D-shaped shaft and is sold individually.
$33.12
Special Order
D-Shaped Knob Clip
PartSelect #: PS268493
Manufacturer #: WH01X10106
Sold individually.
$11.45
Special Order
Tub Seal
PartSelect #: PS4704237
Manufacturer #: WH02X10383
The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably ...
$25.45
Special Order
Dual Action Agitator
PartSelect #: PS1482519
Manufacturer #: WH43X10034
This does not come with the fabric dispenser - must order separately or use original part.
$150.31
Special Order
Tub Bearing
PartSelect #: PS271510
Manufacturer #: WH2X1198
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you...
$34.99
Special Order
Dial with Compression Ring
PartSelect #: PS1482363
Manufacturer #: WH11X10049
This timer dial with compression ring shows you which part of the cycle your washer is in. It is white in color and can be found mounted on the timer shaft. You may need to replace this part if your ...
$21.88
Special Order
Drain Hose
PartSelect #: PS890597
Manufacturer #: WH41X10096
This drain hose is a replacement part for your top-loading washer. The hose measures 57 inches in length.
$74.14
Special Order
Split Ring
PartSelect #: PS1766022
Manufacturer #: WH02X10265
This split ring is two inches in diameter.
$18.32
Special Order
6-Rib Drive Belt
PartSelect #: PS1482278
Manufacturer #: WH01X10302
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
$45.99
Special Order
Questions And Answers for GTWN2800D1WW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Davis
December 5, 2019
Seems to agitate very slowly is this normal?
For model number GTWN2800D1WW
Hello Davis, thank you for writing. Replacing the Agitator Coupling, part number PS1482517 for your model washer should improve this. Good luck with your repair!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Eric
March 9, 2023
Does this machine have a filter for the drain?
For model number GTWN2800D1WW
Hello Eric, thank you for contacting us. According to our research, your model does not contain any filters for the drain. We hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
September 2, 2022
Clothes are still wet after spin cycle. Also little water puddles in the Tub. Have to run spin cycle twice. What could be causing this?
For model number GTWN2800D1WW
Hi Mike, thank you for contacting us. Most of the times, for a washer that spins but still turns out wet clothing, this is a drain hose problem. It could be clogged, kinked, or positioned incorrectly. You will also need to clean the drain filter, located behind a small access panel at the bottom of the washer. Open the panel, take out the filter, and remove any accumulated debris. If the filter has checked out, the next thing to do is to check the drain pump. You can access the drain pump by removing the drain hose and the back panel of your washer. Check for debris, which should be obvious to see. If you find no blockages, you will need to test the drain pump to see if it is actually working properly. Test the pump for continuity using a multimeter. A reading other than 5-10 ohms means the pump has malfunctioned and needs replacement. You will also need to check the belt. Over time, the belt that helps spin the washer drum can become stretched, which will affect how fast the washer can spin. If the belt is stretched out, it can slide around during the cycle and will not allow the washer to reach the speeds that it needs to in order to remove all excess water. Please contact us anytime if you require further assistance.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Verlene
February 22, 2020
Can the agitator be replaced with an impeller. The existing agitator is ruining my clothes.
For model number GTWN2800D1WW
Hi Verlene,
Thank you for your question. If the agitator in your washer is ruining you clothes, you may be overloading it. If you are overloading the washer, this may cause your clothes to become damaged during the wash cycle. Overloading the washer places a lot of pressure on the bearings, drum and the motor, causing these parts to wear out and become damaged over time. Overloading the washer may also push articles of clothing into the door or under the agitator which would cause them to pull when the washer is running. Try washing the clothes in smaller loads. Also, check the labels on your clothes to see how they should be washed and make sure you are using the correct wash cycle for the clothes that you are washing. Clothes that are considered delicate should be washed by hand. We hope this helps. Thank you and have a great day.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Janet
February 23, 2020
Why washer does not spin and drain sometime
For model number GTWN2800D1WW
Hello Janet, Thank you for the question. We suggest checking the Lid Switch, PartSelect Number PS1482372 to see if the wiring is loose or the switch is damaged. If damaged, it will not allow the Spin and drain cycle to start. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- 2
- 3
- Next >
Common Symptoms of the GTWN2800D1WW
[Viewing 12 of 12]Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Control knob teeth were worn
I spoke to a very nice young ladie who took my order and I received my order within two days. I pull the clasp off of the old knob and replace the knob and the clasp with the new part and it now works great. Thank you for helping me find the part I needed.
Parts Used:
-
Charles from Dallas, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
507 of 511 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The original Knob just fell apart
The repair was so easy when I got the part, I did it myself without any help in 5 seconds!
Parts Used:
-
Irina from Englewood, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
380 of 390 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washing machine would not go through all cycles or agitate
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.
Parts Used:
-
Brian from Millerplace, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
227 of 286 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!