Models
>
GU2275XTVY0
GU2275XTVY0 Whirlpool Dishwasher - Overview
Sections of the GU2275XTVY0
[Viewing 12 of 12]Manuals & Care Guides for GU2275XTVY0
Click to downloadInstall
Installation Instructions
(14.97MB)
Install
Installation Instructions
(10.38MB)
Manual
Owner's Manuals
(1.75MB)
Keep searches simple, eg. "belt" or "pump".
Rack Track Stop
PartSelect #: PS11746591
Manufacturer #: WP8565925
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
$9.80
In Stock
Water Inlet Valve
PartSelect #: PS11749213
Manufacturer #: WPW10158389
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$75.63
In Stock
Mounting Bracket
PartSelect #: PS11745496
Manufacturer #: WP8269145
Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.
$12.76
In Stock
Chopper Assembly
PartSelect #: PS1734917
Manufacturer #: W10083957
This chopper assembly chops up/mince the food particles to prevent from clogging the dishwasher pump.
$44.20
In Stock
Dishwasher Heating Element
PartSelect #: PS8260087
Manufacturer #: W10518394
This manufacturer-certified heating element is used to create heat during the dry cycle and increase water temperature during portions of the wash cycle when certain options are selected. If your dish...
$84.09
In Stock
Rinse-Aid Dispenser Cap
PartSelect #: PS11746426
Manufacturer #: WP8558307
The rinse aid cap (sometimes referred to as the dispenser cap), covers the rinse aid dispenser on the dishwasher door. If your dishwasher will not dispense detergent, or it is leaking detergent, there...
$35.06
In Stock
Bi-Metal Fuse
PartSelect #: PS2360984
Manufacturer #: W10258275
This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit in the appliance. Als...
$43.91
In Stock
Dishwasher Door Gasket with Strike - Black
PartSelect #: PS5136129
Manufacturer #: W10542314
$97.15
In Stock
Friction Sleeve
PartSelect #: PS11745488
Manufacturer #: WP8268961
This part helps to keep your door quiet when it opens and closes.
$9.53
In Stock
Spinner Kit
PartSelect #: PS972316
Manufacturer #: 8193983
This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.
$37.53
In Stock
Questions And Answers for GU2275XTVY0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
RALPH
March 4, 2020
During wash cycle water leaks out at lower fight side of door
For model number GU2275XTVY0
Hello, Thank you for your question. Looking at your model you will need to look into this part- PartSelect Number PS5136129. We hope this helps.
Was this helpful?
Thank you for voting!
Sylvia
January 20, 2022
Appliance is not taking on water except when I completed the reset procedure and even then on an intermittent basis
For model number GU2275XTVY0
Hello Sylvia, Thank you for the question. We suggest testing the Water Inlet Valve. Use your multitester to test the valve for continuity. Set the device to the ohms setting x 1. Touch each of the meter's probes to a terminal. If you receive a reading of infinity, it means the valve's solenoid is faulty and the valve needs to be replaced. If your valve has two solenoids (four terminals), test the second pair of terminals in the same manner. If either pair of terminals receives a result of infinity, replace the water inlet valve. We hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
Tewelde
February 6, 2020
My dishwasher drains the first portion of the cycle but does not drain the last cycle. If push drain it will drain ok. Any idea which part is bad?
For model number GU2275XTVY0
Hello Tewelde, thank you for your question. We would recommend checking the drain hose, and check valve to be sure the hose is not clogged or the check valve has become loose or broken. If those parts are ok, you might want to check the turbidity sensor. I hope this helps.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the GU2275XTVY0
[Viewing 10 of 10]Leaking
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
Parts Used:
-
Andrew from Alexandria, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
479 of 532 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud grinding noise from water pump
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
Parts Used:
-
Steve from Inver Grove Heights, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
221 of 249 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heater element broken.
Step 1: Remove the screws in the bottom of the countertop.
Step 2: Remove the screws holding the bottom kickplate.
Step 3: Loosen leveling legs.
Step 4: Pull dishwasher out of hole.
Step 5: Unlplug dishwasher.
Step 6: Disconnect wires from bottom of element in back.
Step 7: Remove plastic nuts holding element in place.
Step 8: Remove element.
Step 9: Reverse Steps 1-7.
Step 10: Drink beer.
Step 2: Remove the screws holding the bottom kickplate.
Step 3: Loosen leveling legs.
Step 4: Pull dishwasher out of hole.
Step 5: Unlplug dishwasher.
Step 6: Disconnect wires from bottom of element in back.
Step 7: Remove plastic nuts holding element in place.
Step 8: Remove element.
Step 9: Reverse Steps 1-7.
Step 10: Drink beer.
Parts Used:
-
Dennis from Sedro Woolley, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Wrench set
218 of 245 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!