![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)
Electronic Control Board
Fits your AD50USL4!
$103.00
Special Order
Fits your AD50USL4!
PartSelect Number
PS11738436
Manufacturer Part Number
WP1187912
Manufactured by
Whirlpool
Troubleshooting
This part works with the following products:
Dehumidifier.
This part works with the following products:
Whirlpool.
Part# WP1187912 replaces these:
1184916, 1187912
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 1 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
bad control on 1998 Whirlpool dehumidifier
Disassemble all the housings starting with front cover, top, sheetmetal side/back piece and top styrofoam support. The top slides back 3/8" before you can lift it up off the keys. Carefully pry/pop the control board loose from the top piece and swap all the wires. Had to cut loose 2 zip-ties to re-route the tank switch wires: immediately replace with new zip-tie left full loose so new wires can be re-routed without wiring bundle falling all over. Get all the wires positioned and finish tightening up the zip-ties, but not all the way, just like the factory did. Cut the tails on the ties.
While all the housings were off I vacuumed off the parts and coils and washed the fan blades off with soapy water and a sponge. Looked for chafed wires and such. Trimmed the coil case up with sheet metal shears where it was rubbing on the styrofoam bottom tray and gently filed the cut smooth.
Reassembly: snap the board back into the top piece, put the styrofoam top support on, then the side/back metal, then the top, dropping it onto the keys and sliding it forward again. The front piece goes on last.
While all the housings were off I vacuumed off the parts and coils and washed the fan blades off with soapy water and a sponge. Looked for chafed wires and such. Trimmed the coil case up with sheet metal shears where it was rubbing on the styrofoam bottom tray and gently filed the cut smooth.
Reassembly: snap the board back into the top piece, put the styrofoam top support on, then the side/back metal, then the top, dropping it onto the keys and sliding it forward again. The front piece goes on last.
Other Parts Used:
-
Alan Van from Springfield, OR
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Steve
May 16, 2019
Does the control board wp1187912 contain the humidistat?
For model number AD65USM2
Hello Steve, thank you for contacting us. Yes, it is included in this Electronic Control Board on your model.
1 person found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11738436
Manufacturer Part Number: WP1187912
Manufacturer Part Number: WP1187912
Brand
Model Number
Description
![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)