Inner Door Liner with Vent
$238.82
In Stock
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
PartSelect Number
PS2020827
Manufacturer Part Number
22003083
Manufactured by
Whirlpool
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Maytag.
Part# 22003083 replaces these:
AP4027714, 785455, 22002252, 22002355, 22002446, 22002539, 22003076, 22003083, 22003208, 33002210
Customer Repair Stories
Average Repair Rating: 3.6 / 5.0, 3 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The door liner broke while my wife was washing a comforter
Taking off the old door and removing the inner door line was relatively easy. I believe I had to remove a total of 8 screws to completely remove the hinges and gain access to the inner panel. Removing the vent tume and grommet was easy, however, I regret not taking a picture of the door latch assembly before removing the vent tube. The door latch is held in by a pair of springs and I had a heck of a time getting the springs back on the door frame assembly. I don't know if I attached it correctly, but the washer locks properly! Attaching the vent tube itself was not that difficult but the same cannot be said of the vent grommet. There was no way to get this grommet in the bottom opening without distorting it or tearing it apart. I finally had to slide it up on the vent tube assembly and basically force it down into the bottom opening. It was not the easiest task to do and I spent more time fiddling about with this stupid grommet than I did with the entire repair. The one thing I would caution anyone doing this repair in the future is to pay close attention to how the speed nuts are installed on the exterior door frame when you go to attach the inner liner. If you do not install them properly you will not be able to attach the inner liner to the exterior door panel.
Other Parts Used:
-
Ted from Chicago, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washed a stroller seat w/ a semi hard plastic back and it wore a large friction hole in the door liner.
First I removed the door itself from the unit by taking out 2 screws and lifting the door slightly so that the hinges can slide out of their slots. I then preceded to remove the liner assembly from the door. Once all the screws where removed I separated the liner from the door and continued to remove the additional hardware from the damaged liner and transfered it to the new one. I paid close attention to how items were removed but other than the hinges, all other items can only fit one way. The liner was then replaced and the door put back on the unit. Pay close attention to the door hinges, reattaching them wrong won't allow the door to line up or close properly.
Other Parts Used:
-
Mike from Kissimmee, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
inner panel of washer door had been damaged/worn through
removed phillips headed screws from sides (hinge on one side) and bottome of door, placed door flat on counter top. Removed interior vent, disassembled the door latching mechanism - somewhat difficult to figure out because needed to undo snapped in parts (used flat screwdriver to pry). Then removed inner panel from door, placed new inner panel into door interior, reassembled door latch mechaninsm, replaced vent tube. screwed in phillips head screws to bottom and non-hinged side of door. Brought door back over to machine and attached hinges to door.
Other Parts Used:
-
anthony from SAINT CHARLES, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2020827
Manufacturer Part Number: 22003083
Manufacturer Part Number: 22003083
Brand
Model Number
Description