Part Location Diagram of WH43X10037 GE COUPLING PULSATOR
See part 310 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

COUPLING PULSATOR

$17.91
  Special Order
PartSelect Number PS2340064
Manufacturer Part Number WH43X10037
Manufactured by GE
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
General Electric.
Part# WH43X10037 replaces these:
AP4362881
Back to Top
Customer Repair Stories
 Average Repair Rating: 3.8 / 5.0, 1 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
While washing in agitation cycle only! A metal on metal grinding screech was emitted with each agitation each back & forth adgitation
Removed center fabric softener cup. removed agitator holding NUT & washer. Lifted off agitator. Pried off Coupling Pulsator.
Cleaned off all parts (soap Scum )
Installed new Coupling Pulsator (tapped gently down with wood hammer handle) Installed agitator& hold down nut&washer. Installed softener cup.
Job done & noise gone .
Thanks Part Select
Other Parts Used:
  • anthony from HUNTINGTON, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

4 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Art
November 19, 2018
The coupling pulsator is jamed or stuck, any advice on how i should remove it
For model number Gtwn4950lows
PartSelect logo
Hi Art, thank you for your question. You should be able to just slide this part upward. You might need to use a non staining lubricant to try and help slip it off the shaft. You may need to use pliers or something that would grip it tightly to help pull it off. Unfortunately the manufacturer does not offer any suggestions for an issue like this. If you have a thin enough pry bar, you might be able to slip it just underneath of the coupling and force it up that was as well. If worst comes to worst, I could suggest perhaps carefully splitting the part so that you do not damage the drive shaft but are able to remove the old coupling after it is in pieces. I hope that helps. Good luck with your repair.

7 people found this helpful.

Was this helpful?
Thank you for voting!
Greg
August 3, 2018
How do you remove the pulsator coupler?
For model number WHRE5550K2WW
PartSelect logo
Hi Greg, Thank you for your question. You would have to remove your agitator so that you can replace this part. All you do to do that is remove the dispenser in the middle but turning it counter clockwise. Then unscrew the bolt and lift the agitator off of your drive block. You should be able to pull this part off and then install the new one. I hope that helps. Good luck with your repair.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Toni
July 9, 2019
I need help with figuring out what’s wrong with my washer. I’ve reset and nothing. The motor is blinking a error code of 1flash per 3second. 1blink...123....1blink. if you could help me understand why it’s not agitating and how to go check what may need to be replaced would be great. thank you in advance.
For model number Wpre6150k2wt
PartSelect logo
Hello Toni, thank you for your question. The most common causes of the washer not starting is the PartSelect Number: PS1482371, Triple Water Inlet Valve PartSelect Number: PS2354072, and PROBE SENSOR ATC PartSelect Number: PS2355966. We would recommend testing these parts first. I hope this helps!

Was this helpful?
Thank you for voting!
Jose
February 12, 2020
When washing washer makes noise when agitating
For model number WHRE5550K2WW
PartSelect logo
Hi Jose, thank you for your question. There are a couple of parts that you may want to check. First you should take a look at your tub bearing and all of the washers and tub seal that are in the same area. Look for any damage to the parts. If those parts are fine then the issue might be in your shifter assembly. Good luck with your repair.

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2340064
Manufacturer Part Number: WH43X10037
Brand
Model Number
Description
General Electric
58971K0WW
General Electric
58971K2WW
Washer
General Electric
58971K3WW
Washer
General Electric
EWA5600K0WW
Washer
General Electric
EWA5600K1WW
Washer
General Electric
EWA5600K2WW
Washer
General Electric
EWA5600K3WW
Washer
General Electric
GCWN4950D0WS
Washer
General Electric
GCWN4950D1WS
Washer
General Electric
GCWN4950D2WS
Washer - WASHER
General Electric
GCWN5050M0WS
Washer
General Electric
GCWN5050M1WS
Washer
General Electric
GCWN5550D0WW
Washer
General Electric
GHRE5550K0WW
Washer
General Electric
GHRE5550K2WW
Washer
General Electric
GHRE5550K3WW
Washer
General Electric
GJRE5500K0WW
Washer
General Electric
GJRE5500K2WW
Washer
General Electric
GJRE5500K3WW
Washer
General Electric
GLWN5050M0WS
Washer
General Electric
GLWN5050M1WS
Washer
General Electric
GLWN5550D0WW
Washer
General Electric
GLWN5550D1WW
Washer
General Electric
GPRE8350K0WT
Washer
General Electric
GPRE8350K2WT
Washer
General Electric
GPRE8350K3WT
Washer
General Electric
GRWN5150M0WS
Washer
General Electric
GRWN5150M1WS
Washer
General Electric
GRWN5550D0WS
Washer
General Electric
GRWN5550D0WW
Washer
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service